If you want to learn more, please visit our website.
While KSB GIW, Inc.'s pumps help our customers succeed every day, some materials can break down over time &#; either from misuse or from contact with abrasive or corrosive materials. One customer recently experienced a leak that resulted from a worn shaft sleeve. Here&#;s how the problem was resolved, as well as some recommended ways for customers to avoid shaft sleeve problems in the future.
The issue
Shaft sleeves are cylindrical metal tubes designed to protect pump shafts from erosion, corrosion, and wear at critical points, such as at the stuffing box. The shaft sleeve is a wear component, like brake pads on a car, and is designed to be more time- and cost-efficient to replace than the shaft itself (like the entire braking system).
The customer in question discovered during an inspection that dirty seal water had cut their shaft sleeve in half, causing a leak. As a temporary measure, the millwright tightened the sleeve and moved it inward; however, this caused a secondary wear pattern and did not stop the leak. A second tightening prevented the sleeve from rotating and caused a horizontal wear pattern in one location. By this point, the customer should have realized that the sleeve was beyond repair. If wear patterns have already formed on the shaft sleeve, moving it will only worsen the wear and cause new wear patterns to form in the area relative to its original cause.
To better understand this, think of slurry and contaminated sealing water like liquid sand paper. Both can be highly corrosive and abrasive. Moving the shaft sleeve will only relocate the groove and initiate the generation of another one. Tightening the gland compresses the packing and reduces the cooling effect of the sealing water; over-tightening it will make matters worse and can lead to component failure.
The solution
To prevent failure from occurring, you can take a few steps to diagnose and solve problems with the shaft sleeve before it wears out. Make this diagnosis a part of your routine pump maintenance in order to avoid early sleeve replacement.
The first step is to inspect the sealing water system for adequate flow, pressure, and quality. KSB GIW, Inc. recommends clean sealing water at a sustained pressure of 10 PSI above the discharge pressure of the pump. The higher-pressure sealing water will prevent the pumped medium from weeping back into the stuffing box, thereby mitigating shaft sleeve wear. If the flow and pressure are within specifications, check the sealing water for corrosive properties and/or abrasive particulates. The shaft sealing system must be designed and applied according to the parameters for the pump.
If you have inspected the system and found that the shaft sleeve is worn beyond repair or leaking, it may be time to replace it. Fortunately, shaft sleeves are designed to be more time- and cost-efficient to replace than the entire shaft, making replacement a &#;no brainer&#; as far as cost and repair time are concerned. Shaft sleeves are available in different materials to combat all combinations of wear and corrosion.
Do you have questions about your pump or specific parts, such as the shaft sleeve? Get in touch with us todayHow KSB GIW, Inc. can help
As part of the KSB GIW, Inc. catalog of pumps and pump parts, we offer over 15 different shaft sleeve material options, available for an array of industrial applications. Our shaft sleeve materials are designed for use in corrosive as well as erosive environments. When paired with the correct stuffing box assembly, our shaft sealing arrangements are designed to tackle even the most challenging pumping applications. We also offer two types of sleeves: the Conventional Type, which is used in combination with an Impeller Release Ring assembly; and the Hook Type, which is not.
All of our shaft sleeves, as well as most of our other products, are available in multiple material options. It&#;s critical that the correct materials be selected for all products in order to meet customers&#; ever-changing pumping needs. One such material is the nickel-chromium coated 0SFWS, which has been chosen as our standard shaft sleeve offering due to its success in a wide range of applications and its cost effectiveness.
If your shaft sleeve is worn to the point of leakage, you should consider replacing it. While replacing the sleeve is easier and less expensive than replacing the entire shaft, the process can interfere with and slow down your overall production. Therefore, it&#;s important to exercise best maintenance practices to extend the life of your shaft sleeve. You can do this by understanding what contributes to shaft wear and knowing the specifications of your particular pump related to flow, pressure, and sealing water. Finally, if your shaft sleeve is leaking, contact KSB GIW, Inc. about a replacement before the leak damages the rest of the shaft.
Understanding The Advantages Of A Pump&#;s Shaft Sleeve
Shaft sleeves are frequently ignored and undervalued in pump design. However, for you to use shaft sleeves efficiently in upcoming projects, we&#;ve highlighted their significance and the top advantages of pump shaft sleeves in this post.
What does a pump&#;s shaft sleeve do?
The pump shaft has a component called a shaft sleeve installed on it to lessen wear and tear. It&#;s crucial to choose the shaft sleeve that best suits the pump because they come in various sizes and forms.
Variety of Pumps
Mechanically sealed pumps and sealless pumps are the two primary divisions of pumps.
Pumps that are mechanically sealed: These pumps have a closing device called a mechanical seal that physically blocks the flow of fluid and air into and out of the pump. The centrifugal pump is the most prevalent kind of mechanically sealed pump.
Additional reading:4 Tips to Select the Right Metso Slurry Pump Components
How to Select the Right Metso Slurry Pump Components?SUNBO PUMP contains other products and information you need, so please check it out.
Pumps without a mechanical seal that uses a fluid seal to keep fluid and air from entering or leaving the pump are known as sealless pumps. The piston pump is the most prevalent kind of sealless pump.
Uses for Junty Shaft Sleeve in Pumps
The enhancement of fluid flow is just one of the several uses for Junty shaft sleeve in pumps. It accomplishes this by ensuring a snug fit around the pump shaft, which in turn lessens the amount of air that can enter and obstruct liquid flow. The shaft sleeve can also aid in keeping the impeller of the pump clear of debris.
What Advantages Do Junty Shaft Sleeves in Pumps Offer?
An essential component of the pump that improves performance and efficiency is the junky shaft sleeve. The following are some advantages of a shaft sleeve in a pump:
Increased Durability &#; Junty shaft sleeves are frequently composed of high-quality materials, which increase their durability. This makes it simpler to maintain the pump&#;s smooth operation and effectiveness over extended periods.
Improved Performance &#; By reducing friction and wear on parts, junk shaft sleeves help pumps perform better. Increased productivity and efficiency can result from this.
Reduced Maintenance Costs &#; Junk shaft sleeves can lessen pump maintenance frequency, ultimately saving you money.
Productivity Gains &#; Junk shaft sleeves allow workers to work more efficiently because they don&#;t have to spend time repairing excessive wear and friction on their tools.
Conclusion
This article covers the best qualities of shaft sleeves in a pump. Please don&#;t hesitate to contact Junty if you have any questions or are interested!
The company is the world’s best Ceramic Shaft Sleeve supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.
Comments
All Comments (0)