View topic - Buyer's Guide - a good read

by muley » Fri 09.06., 09:13

For more information, please visit Gearbox Oil Seal Manufacturer.

Buyer&#;s Guide

OK, you&#;ve set aside the budget, won the lottery or had a bit of luck. Your thoughts turn to a sports car &#; well, you should do it at least once. You don&#;t want to spend too much money on it, you&#;d like to out-perform a Porsche Boxster for mid-range acceleration and have a usable car with a convertible roof. You might consider an MX-5 or a Celica Convertible or a TVR but eventually decide on the M100 Élan &#; full of character, pedigree and a delight to drive. You peruse

Starting at the front,

Under the

bumper

there is a Rubber lip &#; past encounters with kerbs, small mammals or spare bricks left on the Queen&#;s highway may have damaged it. They are not particularly hard to get hold of but are held on by many screws. If it is damaged the bumper itself may have suffered as well &#; look for chips and cracks.
Fast cars suffer from

Stone chips

and the M100 Élan is no exception. These can be found in most places all over the front of the car and on the mirror covers. Blue cars seem to suffer particularly badly from this. The front end can be re-sprayed for anything between £400 and £ or you could live with it.
It&#;s now time to get down to it. Get on your knees and look under the front there should be a black plastic Cover or under tray under the radiator straight behind the bumper extending the width of the car. If it is not present this is a sign of neglect and may have mean that the radiator support has been exposed to salt and wet. Look for signs of water / coolant stains on or around this area - it could point to a leaking radiator and/or hoses. Not particularly expensive to fix.
While you are on your knees looking underneath the front examine the

Prongeron

&#; this is the metal bit running between the front wheels down the middle of the car towards the bumper. It has a &#;do not jack&#; sticker on it, but some less scrupulous owners and garages choose to ignore this and it may have dents where trolley jacks have been used on it. This can distort this important part of the car&#;s chassis &#; it might not necessarily be a bad thing but points to lack of care on behalf of the owners and / or garages. A few Élans have been seen with area and other bits of the chassis sprayed with a black under seal-like substance &#; this was supposed to happen as part of the anti-corrosion regime by the Lotus dealer network and it quite normal(?).
Before you stand up take a glance at the

Track Control arms

&#; these can corrode quite badly but would have to be really bad if you wanted to spot it on a quick inspection &#; ideally you&#;d take the wheels off and bang them with a hammer to check!

OK, you can stand up and dust your knees off. Stand back and check the

Panel fit

&#; bonnet, pods, clam and bumper &#; the gaps between these items should be even all across the front and round to the wheel arch. If there are odd gaps this might point to body damage in the past. Check that the pods and bonnet are level. On some cars the front of the door catches on the rear of the panel behind the front wheel arch. This is quite common and can be fixed with a bit of adjustment / coaxing with a mallet.
Look at the

Wheels

, do they have any dents or scuffing? They can be refurbished for not too much money or bought second-hand. Are they the original wheels? You might not be bothered by after-market replacements but some purists are.

Poke your finger through the spokes and run it across the disk &#; is there a &#;lip&#; at the edge? If so, they might need replacing, but standard ones are very cheap. Check pad wear, too, standard pads are cheap. There are a few upgrade options for the

front brakes

, generally speaking they are a good idea because the standard brakes are relatively poor and do not match the performance of the car if it is used energetically.

Look at the

tyres

. Are all the Tyres the same? Do they at least match on the same &#;axle&#; front and rear? Are they worn? If worn they should be worn evenly otherwise this could point to tracking / toe-in problems.
Most Élans will have had at least one replacement

Exhaust

by now &#; at least the rear box. Have a look at the rear box ; ideally this will be stainless steel and should appear reasonably shiny. If there are any holes in the system, this would be picked up in the MOT Test. In any case, they are not particularly expensive to replace (thanks to LEC group buys &#; an upgrade here can yield performance benefits)
Still standing up, put your finger through the spokes and see if there is a lip on the

Rear disks

; glance at the pads, too. The rear brakes are relatively expensive to replace.

Next we move on to the

Hood

&#; I&#;m assuming it is up at this point! - check the rear edge is sitting firmly on to the deck at the rear. If it isn&#;t it is possible that the tensioning wires are broken or need adjustment. This is a task best left to the experts! It is a quirk of Élan hoods that a wear point occurs where the frame touches it every time it is deployed &#; check that this hasn&#;t left a hole just above the tail end of the window, or that it has been re-inforced or patched. The Condition of

rear window

should be checked if it is very opaque it might well need replacing if the rest of the hood is OK otherwise expect to shell out for a new hood. It is important to check the condition of the rubbers seals around the windows &#; these are expensive (if you can find any) and fiddly to replace and if they are in poor condition, with cuts or chunks missing you will definitely suffer when it is raining!.

While we are that back borrow the Boot key open the boot and inspect the interior. If the boot key is worn and there is only one and you do decide to buy the car, it can be tricky to find a locksmith with the correct American GM blanks &#; you have been warned. Check the carpets are clean and present, lift them up and check the Jack / wrench and Space saver are present. You might be lucky and find a

Tool kit

in the well at the left hand side &#; these were originally supplied with the car &#; the tools are not overly useful &#; if you are a hands on type you&#;ll already have better but it is a nice feature nonetheless &#; especially if it is entirely complete with the penknife (not all kits had that).

Close the boot and look carefully at the

Rear lights

&#; they are rather large and if cracked can be expensive to replace although they have been seen on eBay for around £100. Look at the Rear number plate. Early Élans had a Perspex cover flush with the light assemblies, later ones and S2s have a recessed plinth mounting. Number plates under the cover have been known to suffer and decay make sure it&#;s Ok, but they&#;re very cheap to replace if not.

Time to get on out knees at the rear of the car to examine the &#;Achilles Heel&#; of the M100 Élan the

Rear lower wishbones

If you want to learn more, please visit our website Oil Seal for Sale.

Additional reading:
Oil seal: how do I install it correctly? - ERIKs. If it is an S2 it will have galvanised wishbones so you won&#;t have a problem but earlier SEs or NAs will suffer unless they have been effectively rust proofed. If you&#;re a &#;hands on&#; sort of person they&#;re pretty straightforward to replace and galvanised replacements are easy to come by. If not, you may have to pay up to £ to get them replaced professionally. Again, glancing at them won&#;t help an awful lot &#; you really need to belt them with a hammer or the wheel brace &#; if you hear a muffled thud you may have a problem.

Moving to the front of the car, it&#;s time to look under the bonnet. Bonnet stay should be present and correct and clip neatly into a clip at the rear of the bonnet. Have a look and note any New jubilee clips this normally means a hose here or there has been replaced which is a good sign. Look, too, at the General cleanliness ; if it is really dirty and shabby it may not have been looked after. The engines are pretty oil tight apart from the

cam angle sensor oil seal

this can create an oily mess on the right hand side of the engine but it cheap and easy to fix.
You may find an enthusiast has butchered some of the hoses and pipes and fitted Blow off valves, manual boost controls or KN filter. Some of these have been done on a neat manner, some not so neat. It&#;s a matter of personal taste, you may prefer your Élan in an original state. Look for any water Leaks near the thermostat or radiator connections.
Unscrew the oil filler cap and look for any Residue &#; if you see some mayonnaise like substance there this could mean the head gasket is faulty. Normally the oil in an Élan is fairly clean and has to be changed every 6 months in the turbo &#;equipped SEs and S2s &#; pull out the dipstick and check the colour of the oil, if you see anything other than oil, for example beads of water there might be a problem with the head gasket. While on the subject of fluids, look at the brake fluid reservoir &#; the brake fluid should be clean and clear as changing the brake fluid is part of the B service and should be done every couple of years or so.

The underneath of the Élan bonnet should have a layer of Sound deadening material this should be sound and smooth. One car I looked at had this hanging down and it had got damp from a leak in the washer jets then it had created a damp situation on the throttle cable which shed it&#;s plastic coating and rusted away. The area where the Throttle cable fits into a clip can result in the plastic coating eroding and the metal outer rusting &#; not too expensive but a swine to fit. Finally, while under the bonnet look at the &#;

Swan neck

area&#; &#; inboard and at the rear of the light pods a part of the clamshell curves in an S shape. If this area is anything other than smooth or has cracks or chips in it, then the likelihood is that the car has had a knock at the front at some stage. Have a close look at the

chassis sticker

. It&#;s not an embossed brass plaque but a piece of paper under a sheet of plastic. If it is missing or looks like a photocopy stuck under a piece of sellotape then be concerned. It might be that the car has had a respray but even then it should be properly fixed. OK, we&#;ve finished under the bonnet, but we might get a helper or the owner to start the engine. Listen for any knocks or rattles. If the engine is cold, you should expect to see about 5 bar on the

oil pressure

gauge on tickover. When warm, it should drop to around 1/2 way between the 2.5 bar and 5 bar mark on tickover and be around the 5 bar mark at 3,000 rpm. It is quite normal for a tapping noise from the, er, tappets on start-up &#; they are hydraulic and until the pressure builds up the clearances are too high resulting in a tapping noise. This noise should go away, if not in a few minutes then after a run on the road when the engine has warmed up fully. Close the bonnet.

Check with the owner to ensure you will get all the

keys

. The Élan often came with a factory-fit alarm or immobiliser otherwise they have been fitted with one as stipulated by the insurance company. Make sure you get 2 sets of keys and remote control blippers, it&#;s good to have a spare set and it can be a pain getting copies.

OK, that completes our study of the exterior, let us open the door and look inside. Check the condition of the

Seats

. Some Élans may have a sagging seat base especially on the driver&#;s side [the most used seat], this looks pretty awful but is simply due to some small c shaped clips failing. They are cheap and easy to replace and can transform the look of the seat as well as providing a more comfortable ride. SE and NA Élans had the option of a leather interior, this was in striped panels keyed into the door cards as well. The panels would be yellow or red depending on the body colour. S2s came with a different pattern set &#; the stripes were dropped and they came in grey or magnolia. Some cars may have had a retrim- all the ones I&#;ve seen have been done very well and can transform the interior. Have a look at the

Carpets

. There should be overcarpets to protect the main carpet, proper Lotus ones would be preferable, but if they&#;re worn they can be replaced. Put the hood down &#; with the owner&#;s help &#; if it not down already. Marvel at how easy it is and how neat it looks with the hood down. Look at the

B post caps

just behind the seat, these should be present and correct. They are hard to get hold of and fiddly to fix. The Élan looks nicer with them in place. Glance around the cockpit and make sure they are no scuffs or scratches on the dashboard or console. Now start the engine, it should fire up straight away and settle to a smooth idle. I recommend putting the hood back up for the test drive as any mechanical noises will be more apparent with the hood up. Check the operation of the

remote electric mirr

ors and ensure the

electric wind

ows go up and down smoothly. Parts to fix these can be obtained but are a pig to fit - either taking up a lot of your time or costing you a lot at a specialist! Voltmeter should be showing around 14Volts with the engine running. Make sure the rev counter and speedo work.

Take it for a drive

(with the owner&#;s permission and if you have insurance. If you are driving on your own policy you will only be covered for third party risks, any damage to the car you are driving is not covered. Take care with this point).

Look out for gear changes, make sure you can change up and down smoothly, any resistance felt going into a gear can point to gearbox trouble. When the engine is hot, accelerate hard from about 3,000 r.p.m. Check you are not leaving a plume of white smoke behind which can point to a potential problem with the

oil seals

in the turbo (this doesn&#;t apply to NA models, of course). Élan engines are pretty bullet-proof and should not smoke much at all.

While Steering at low speeds as you approach full lock you will hear a hissing noise

, this is very normal on the Élan and is nothing to worry about.

It is quite normal for some leaks in wet weather, water will trickle down the windows and / or door pillars this is fairly normal, but it shouldn&#;t be too excessive. Keep an old towel in the car!

Time to look at the

paperwork

, you will want to see the Service history which will be stamps in the owner&#;s handbook or notes made by the enthusiastic hands on owner. Note the mileage in the history and look at Previous MOTs. Look at the current MOT and check there are not too many serious potential faults; obviously it makes sense to buy a car with a long MOT because this postpones the day when you may have to spend money on the car. An MOT test will cover most of the &#;inspect&#; items on and Élan service so it is a good thing to have. Make sure the average mileage tallies with the condition of the car and the service intervals. Some owners keep Bills for work done, have a good read of these and you can see what has been replaced and determine what hasn&#;t &#; consider the likely cost of fixing these items. Get the V5 registration document and check the chassis number matches the chassis number on the sticker under the bonnet. The chassis number is also stamped on the end of the rear chassis outrigger on the right hand side and should be easy to see even with the wheel on.

These are the very worthwhile

upgrades

it would be good to have, if your potential purchase doesn&#;t have them then they should be on your shopping list to be fitted as time and finds allow;

Front brakes upgraded - AP, Hi-Spec or Wilwood if possible.
Galvanised rear wishbones fitted.
Stainless steel exhaust system fitted (2 1/4 to 2 1/2" ideally).
AB gear cables fitted.
ESM chip fitted.
Upgraded dampers fitted.

Start haggling. If you find a good one, you like the colour and the price is right then welcome to the LEC Élan world of motoring.

Trying to pull it all together in one definitive document - this is just a start.Buyer&#;s GuideOK, you&#;ve set aside the budget, won the lottery or had a bit of luck. Your thoughts turn to a sports car &#; well, you should do it at least once. You don&#;t want to spend too much money on it, you&#;d like to out-perform a Porsche Boxster for mid-range acceleration and have a usable car with a convertible roof. You might consider an MX-5 or a Celica Convertible or a TVR but eventually decide on the M100 Élan &#; full of character, pedigree and a delight to drive. You peruse www.lotuselancentral.com , maybe even meet some of the guys there and trawl through the &#;For Sale&#; section, eBay and auto trader. You make an appointment and turn up to look at your first Élan. What do you look for?Starting at the front,Under thethere is a Rubber lip &#; past encounters with kerbs, small mammals or spare bricks left on the Queen&#;s highway may have damaged it. They are not particularly hard to get hold of but are held on by many screws. If it is damaged the bumper itself may have suffered as well &#; look for chips and cracks.Fast cars suffer fromand the M100 Élan is no exception. These can be found in most places all over the front of the car and on the mirror covers. Blue cars seem to suffer particularly badly from this. The front end can be re-sprayed for anything between £400 and £ or you could live with it.It&#;s now time to get down to it. Get on your knees and look under the front there should be a black plastic Cover or under tray under the radiator straight behind the bumper extending the width of the car. If it is not present this is a sign of neglect and may have mean that the radiator support has been exposed to salt and wet. Look for signs of water / coolant stains on or around this area - it could point to a leaking radiator and/or hoses. Not particularly expensive to fix.While you are on your knees looking underneath the front examine the&#; this is the metal bit running between the front wheels down the middle of the car towards the bumper. It has a &#;do not jack&#; sticker on it, but some less scrupulous owners and garages choose to ignore this and it may have dents where trolley jacks have been used on it. This can distort this important part of the car&#;s chassis &#; it might not necessarily be a bad thing but points to lack of care on behalf of the owners and / or garages. A few Élans have been seen with area and other bits of the chassis sprayed with a black under seal-like substance &#; this was supposed to happen as part of the anti-corrosion regime by the Lotus dealer network and it quite normal(?).Before you stand up take a glance at the&#; these can corrode quite badly but would have to be really bad if you wanted to spot it on a quick inspection &#; ideally you&#;d take the wheels off and bang them with a hammer to check!OK, you can stand up and dust your knees off. Stand back and check the&#; bonnet, pods, clam and bumper &#; the gaps between these items should be even all across the front and round to the wheel arch. If there are odd gaps this might point to body damage in the past. Check that the pods and bonnet are level. On some cars the front of the door catches on the rear of the panel behind the front wheel arch. This is quite common and can be fixed with a bit of adjustment / coaxing with a mallet.Look at the, do they have any dents or scuffing? They can be refurbished for not too much money or bought second-hand. Are they the original wheels? You might not be bothered by after-market replacements but some purists are.Poke your finger through the spokes and run it across the disk &#; is there a &#;lip&#; at the edge? If so, they might need replacing, but standard ones are very cheap. Check pad wear, too, standard pads are cheap. There are a few upgrade options for the, generally speaking they are a good idea because the standard brakes are relatively poor and do not match the performance of the car if it is used energetically.Look at the. Are all the Tyres the same? Do they at least match on the same &#;axle&#; front and rear? Are they worn? If worn they should be worn evenly otherwise this could point to tracking / toe-in problems.Most Élans will have had at least one replacementby now &#; at least the rear box. Have a look at the rear box ; ideally this will be stainless steel and should appear reasonably shiny. If there are any holes in the system, this would be picked up in the MOT Test. In any case, they are not particularly expensive to replace (thanks to LEC group buys &#; an upgrade here can yield performance benefits)Still standing up, put your finger through the spokes and see if there is a lip on the; glance at the pads, too. The rear brakes are relatively expensive to replace.Next we move on to the&#; I&#;m assuming it is up at this point! - check the rear edge is sitting firmly on to the deck at the rear. If it isn&#;t it is possible that the tensioning wires are broken or need adjustment. This is a task best left to the experts! It is a quirk of Élan hoods that a wear point occurs where the frame touches it every time it is deployed &#; check that this hasn&#;t left a hole just above the tail end of the window, or that it has been re-inforced or patched. The Condition ofshould be checked if it is very opaque it might well need replacing if the rest of the hood is OK otherwise expect to shell out for a new hood. It is important to check the condition of the rubbers seals around the windows &#; these are expensive (if you can find any) and fiddly to replace and if they are in poor condition, with cuts or chunks missing you will definitely suffer when it is raining!.While we are that back borrow the Boot key open the boot and inspect the interior. If the boot key is worn and there is only one and you do decide to buy the car, it can be tricky to find a locksmith with the correct American GM blanks &#; you have been warned. Check the carpets are clean and present, lift them up and check the Jack / wrench and Space saver are present. You might be lucky and find ain the well at the left hand side &#; these were originally supplied with the car &#; the tools are not overly useful &#; if you are a hands on type you&#;ll already have better but it is a nice feature nonetheless &#; especially if it is entirely complete with the penknife (not all kits had that).Close the boot and look carefully at the&#; they are rather large and if cracked can be expensive to replace although they have been seen on eBay for around £100. Look at the Rear number plate. Early Élans had a Perspex cover flush with the light assemblies, later ones and S2s have a recessed plinth mounting. Number plates under the cover have been known to suffer and decay make sure it&#;s Ok, but they&#;re very cheap to replace if not.Time to get on out knees at the rear of the car to examine the &#;Achilles Heel&#; of the M100 Élan the. If it is an S2 it will have galvanised wishbones so you won&#;t have a problem but earlier SEs or NAs will suffer unless they have been effectively rust proofed. If you&#;re a &#;hands on&#; sort of person they&#;re pretty straightforward to replace and galvanised replacements are easy to come by. If not, you may have to pay up to £ to get them replaced professionally. Again, glancing at them won&#;t help an awful lot &#; you really need to belt them with a hammer or the wheel brace &#; if you hear a muffled thud you may have a problem.Moving to the front of the car, it&#;s time to look under the bonnet. Bonnet stay should be present and correct and clip neatly into a clip at the rear of the bonnet. Have a look and note any New jubilee clips this normally means a hose here or there has been replaced which is a good sign. Look, too, at the General cleanliness ; if it is really dirty and shabby it may not have been looked after. The engines are pretty oil tight apart from thethis can create an oily mess on the right hand side of the engine but it cheap and easy to fix.You may find an enthusiast has butchered some of the hoses and pipes and fitted Blow off valves, manual boost controls or KN filter. Some of these have been done on a neat manner, some not so neat. It&#;s a matter of personal taste, you may prefer your Élan in an original state. Look for any water Leaks near the thermostat or radiator connections.Unscrew the oil filler cap and look for any Residue &#; if you see some mayonnaise like substance there this could mean the head gasket is faulty. Normally the oil in an Élan is fairly clean and has to be changed every 6 months in the turbo &#;equipped SEs and S2s &#; pull out the dipstick and check the colour of the oil, if you see anything other than oil, for example beads of water there might be a problem with the head gasket. While on the subject of fluids, look at the brake fluid reservoir &#; the brake fluid should be clean and clear as changing the brake fluid is part of the B service and should be done every couple of years or so.The underneath of the Élan bonnet should have a layer of Sound deadening material this should be sound and smooth. One car I looked at had this hanging down and it had got damp from a leak in the washer jets then it had created a damp situation on the throttle cable which shed it&#;s plastic coating and rusted away. The area where the Throttle cable fits into a clip can result in the plastic coating eroding and the metal outer rusting &#; not too expensive but a swine to fit. Finally, while under the bonnet look at the &#;area&#; &#; inboard and at the rear of the light pods a part of the clamshell curves in an S shape. If this area is anything other than smooth or has cracks or chips in it, then the likelihood is that the car has had a knock at the front at some stage. Have a close look at the. It&#;s not an embossed brass plaque but a piece of paper under a sheet of plastic. If it is missing or looks like a photocopy stuck under a piece of sellotape then be concerned. It might be that the car has had a respray but even then it should be properly fixed. OK, we&#;ve finished under the bonnet, but we might get a helper or the owner to start the engine. Listen for any knocks or rattles. If the engine is cold, you should expect to see about 5 bar on thegauge on tickover. When warm, it should drop to around 1/2 way between the 2.5 bar and 5 bar mark on tickover and be around the 5 bar mark at 3,000 rpm. It is quite normal for a tapping noise from the, er, tappets on start-up &#; they are hydraulic and until the pressure builds up the clearances are too high resulting in a tapping noise. This noise should go away, if not in a few minutes then after a run on the road when the engine has warmed up fully. Close the bonnet.Check with the owner to ensure you will get all the. The Élan often came with a factory-fit alarm or immobiliser otherwise they have been fitted with one as stipulated by the insurance company. Make sure you get 2 sets of keys and remote control blippers, it&#;s good to have a spare set and it can be a pain getting copies.OK, that completes our study of the exterior, let us open the door and look inside. Check the condition of the. Some Élans may have a sagging seat base especially on the driver&#;s side [the most used seat], this looks pretty awful but is simply due to some small c shaped clips failing. They are cheap and easy to replace and can transform the look of the seat as well as providing a more comfortable ride. SE and NA Élans had the option of a leather interior, this was in striped panels keyed into the door cards as well. The panels would be yellow or red depending on the body colour. S2s came with a different pattern set &#; the stripes were dropped and they came in grey or magnolia. Some cars may have had a retrim- all the ones I&#;ve seen have been done very well and can transform the interior. Have a look at the. There should be overcarpets to protect the main carpet, proper Lotus ones would be preferable, but if they&#;re worn they can be replaced. Put the hood down &#; with the owner&#;s help &#; if it not down already. Marvel at how easy it is and how neat it looks with the hood down. Look at thejust behind the seat, these should be present and correct. They are hard to get hold of and fiddly to fix. The Élan looks nicer with them in place. Glance around the cockpit and make sure they are no scuffs or scratches on the dashboard or console. Now start the engine, it should fire up straight away and settle to a smooth idle. I recommend putting the hood back up for the test drive as any mechanical noises will be more apparent with the hood up. Check the operation of theors and ensure theows go up and down smoothly. Parts to fix these can be obtained but are a pig to fit - either taking up a lot of your time or costing you a lot at a specialist! Voltmeter should be showing around 14Volts with the engine running. Make sure the rev counter and speedo work.Take it for a driveLook out for gear changes, make sure you can change up and down smoothly, any resistance felt going into a gear can point to gearbox trouble. When the engine is hot, accelerate hard from about 3,000 r.p.m. Check you are not leaving a plume of white smoke behind which can point to a potential problem with thein the turbo (this doesn&#;t apply to NA models, of course). Élan engines are pretty bullet-proof and should not smoke much at all., this is very normal on the Élan and is nothing to worry about.It is quite normal for some leaks in wet weather, water will trickle down the windows and / or door pillars this is fairly normal, but it shouldn&#;t be too excessive. Keep an old towel in the car!Time to look at the, you will want to see the Service history which will be stamps in the owner&#;s handbook or notes made by the enthusiastic hands on owner. Note the mileage in the history and look at Previous MOTs. Look at the current MOT and check there are not too many serious potential faults; obviously it makes sense to buy a car with a long MOT because this postpones the day when you may have to spend money on the car. An MOT test will cover most of the &#;inspect&#; items on and Élan service so it is a good thing to have. Make sure the average mileage tallies with the condition of the car and the service intervals. Some owners keep Bills for work done, have a good read of these and you can see what has been replaced and determine what hasn&#;t &#; consider the likely cost of fixing these items. Get the V5 registration document and check the chassis number matches the chassis number on the sticker under the bonnet. The chassis number is also stamped on the end of the rear chassis outrigger on the right hand side and should be easy to see even with the wheel on.These are the very worthwhileit would be good to have, if your potential purchase doesn&#;t have them then they should be on your shopping list to be fitted as time and finds allow;Front brakes upgraded - AP, Hi-Spec or Wilwood if possible.Galvanised rear wishbones fitted.Stainless steel exhaust system fitted (2 1/4 to 2 1/2" ideally).AB gear cables fitted.ESM chip fitted.Upgraded dampers fitted.Start haggling. If you find a good one, you like the colour and the price is right then welcome to the LEC Élan world of motoring.

Contact us to discuss your requirements of Automobile Motorcycle Oil Seal Manufacturer. Our experienced sales team can help you identify the options that best suit your needs.